Close
(0) items
You have no items in your shopping cart.
All Categories
    Filters
    Preferences
    Search

    Lifting Eyes

    Lifting Eyes

    Hoist Rings

    Now also available in 316 stainless steel and metric sizes!

    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for fully vertical lifting only, in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Available in steel with thread sizes from 1/4-20 to 1"-8 (M6 to M16 in metric), and in 316 stainless steel with thread sizes from 1/4-20 to 5/8-11. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in the USA.

    Technical Information

    Hoist-Ring Safety Precautions

    Installation

    Lifting Eyes should be inspected before each use for possible defects and installed by a person trained in the installation of lifting devices. The tapped receiving hole should be countersunk, free of any debris, and deep enough to ensure proper shoulder seating. Firm hand tightening is recommended for installation; do not use wrenches or bars. Angular lifting should be avoided, because angular lifts significantly reduce rated capacity. Any angular loads must be radial in the plane of the eye, never at an angle to that plane. A steel washer or shim may be used under the shoulder to achieve proper eye orientation, but its thickness should not exceed one thread pitch. A washer may also be required to ensure flush seating on rough mounting surfaces.

    carr lane lifting eyes installation guide
    Angular lifting at up to 45° is allowable in this direction (plane of the eye) but load rating is reduced.

    carr lane lifting eyes installation information
    Only straight lifting is allowable in this direction.

    Safety Precautions

    Do not exceed rated load capacity. Maximum load rating applies to straight vertical lifting only. Lifting at an angle reduces load rating significantly – see Dimensions page for reduced load rating at 45° (this reduced rating should be used for any lift other than at 0° vertical). Do not work, stand, or crawl near the load of a Lifting Eye. Do not use a Lifting Eye to lift a load that can rotate; Swivel Hoist Rings should be used for such loads. Do not shock load Lifting Eyes; instead gradually increase lifting of the load to minimize load shock. Do not force hooks or any other fittings into the eye; they must fit freely. Do not weld or machine Lifting Eyes, or perform any repair. Do not expose Lifting Eyes to extreme temperatures or environmental conditions, as this may permanently reduce load capacity. Periodic inspection of installed Lifting Eyes is highly recommended. Also see general Hoist Ring Safety Precautions at the beginning of this catalog section.

    Material

    Steel:
    Forged carbon steel, quenched and drawn, plain finish. DFARS and RoHS compliant.

    Stainless Steel:
    Forged 316 stainless steel, passivated and electropolished. DFARS and RoHS compliant.

    LIFTING EYES

     


    USA
    PART NO. A B C
    DIA
    D
    DIA
    E F
    DIA
    G
    DIA
    H J LOAD RATINGS
    (LBS)
    45º
    CL-4-LE 1/4-20 1 3/4 1-3/16 1-11/32 7/32 17/32 5/32 3/4 500 125
    CL-5-LE 5/16-18 1-1/8 7/8 1-7/16 1-21/32 9/32 19/32 5/32 15/16 900 225
    CL-6-LE 3/8-16 1-1/4 1 1-11/16 1-31/32 11/32 21/32 5/32 1-1/8 1300 325
    CL-8-LE 1/2-13 1-1/2 1-3/16 2-1/8 2-7/16 15/32 29/32 7/32 1-3/8 2400 600
    CL-10-LE 5/8-11 1/3/4 1-3/8 2-9/16 2-15/16 19/32 1-1/32 9/32 1-21/32 4000 1000
    CL-12-LE 3/4-10 2 1-1/2 2-13/16 3-7/32 21/32 1-3/16 9/32 1-13/16 5000 1250
    CL-16-LE 1"-8 2-1/2 1-3/4 3-19/16 4-3/32 29/32 1-9/16 13/32 2-5/16 9000 2250

    HEAVY-DUTY® LIFTING EYES

     


    USA
    PART NO. VERTICAL
    LOAD RATING
    (LBS)
    A B
    CL-36480-HDLE 10000 1"-8 1.00
    CL-36481-HDLE 1" COIL
    CL-36482-HDLE 1-1/4"-7
    CL-36483-HDLE 1-1/4" COIL
    CL-36484-HDLE 15000 1-1/4"-7 1.50
    CL-36485-HDLE 1-1/4" COIL
    CL-36486-HDLE 1-1/2"-6
    CL-36487-HDLE 1-1/2" COIL

    Carr Lane Manufacturing Co.
    View as Grid List
    Sort by
    Display per page

    Heavy-Duty Lifting Eyes

    SKU: CL-Heavy-Duty Lifting Eyes
    MPN: Heavy-Duty Lifting Eyes
    Email Sales for Pricing
    Heavy-Duty® Lifting Eyes have a short, large-diameter thread, making them ideal for lifting heavy plates. Designed for straight vertical lifting only. High-tensile alloy steel. Safety factor = 5:1. Black oxide finish is standard, with cadmium plating available as a special. Patent pending. Made in USA.

    LIFTING EYE CL-10-LE

    SKU: CL-10-LE
    MPN: CL-10-LE
    Email Sales for Pricing
    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for vertical lifting in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in USA.

    LIFTING EYE CL-12-LE

    SKU: CL-12-LE
    MPN: CL-12-LE
    Email Sales for Pricing
    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for vertical lifting in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in USA.

    LIFTING EYE CL-16-LE

    SKU: CL-16-LE
    MPN: CL-16-LE
    Email Sales for Pricing
    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for vertical lifting in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in USA.

    LIFTING EYE CL-4-LE

    SKU: CL-4-LE
    MPN: CL-4-LE
    Email Sales for Pricing
    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for vertical lifting in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in USA.

    LIFTING EYE CL-5-LE

    SKU: CL-5-LE
    MPN: CL-5-LE
    Email Sales for Pricing
    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for vertical lifting in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in USA.

    LIFTING EYE CL-6-LE

    SKU: CL-6-LE
    MPN: CL-6-LE
    Email Sales for Pricing
    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for vertical lifting in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in USA.

    LIFTING EYE CL-8-LE

    SKU: CL-8-LE
    MPN: CL-8-LE
    Email Sales for Pricing
    Lifting Eyes are forged steel eyebolts with an integral shoulder for greater strength. These simple, economical lifting devices are suitable for vertical lifting in-line with the threaded bolt, such as when lifting from a single point or from two points with a spreader bar. For lifting at an angle, Swivel Hoist Rings should be used instead. Manufactured and tested according to ASTM A489 and ANSI B18.15 specifications. Safety factor = 5:1. Made in USA.

    Lifting Eyes