Flexibility--Quickly combine components to satisfy any fixturing requirement.  Through solid construction, our tables and components can be used over and over again, thus reducing future fixture costs.

Quality--Even to the smallest detail, it's improtant to be precise.  That's why Freer Tool& Supply is proud to bring to you Tip Top Welding Tables.

With our quality, pricing, and endless amount of configurable table possibilities, it's easy to see why Freer Tool & Supply is fast becoming the Welding industry's Single Source Solution for all its Fixturing and Table Top needs.

Technical Information
Grid Bores and Grid Distance

3-D Work Table

Our 3-D Work Table is the backbone to our complete Clamping System.  The Work Table is expandable on all five surfaces and is based on a grid system of 100 mm x 100 mm.  The hole separations are within a tolerance of +/- 0.05 mm across the entire matrix.

Material Finish:
ST-52100 (base model)

An advantage of our Work-Tables is that after welding and rough machining they are tension free due to the heat-treated surface.  Because of the grinded work surfaces, a higher level of precision +/- 0.05 mm is achieved on the entire surface.  Therefore these Tables can also be used for Measuring and also as Marking Tables.  The Work Table has a hole grid system of 100 mm x 100 mm withy a bore diameter of 28 mm.  The hole separations are within a tolerance of +/-0.05 mm over the entire matrix.  Countersinking prevents unintentional damage of the grid bores.  Through the regular application of Anti-Spatter Spray, the Work-Table is insensitive to welding beads, dirt, scale, etc.

Clamping Plates with a short flank (100 mm) are the low-cost alternative to the Work-Tables with a long flank (200 mm).  An advantage of our Work-Tables is that after welding and rough machining they are tension free due to the heat-treated surface.  Because of the grinded work surfaces, a higher level of precision +/- 0.05 mm is achieved on the entire surface.  Therefore these Tables can also be used for Measuring and also as Marking Tables.  The Work Table has a hole grid system of 100 mm x 100 mm withy a bore diameter of 28 mm.  The hole separations are within a tolerance of +/-0.05 mm over the entire matrix.  Countersinking prevents unintentional damage of the grid bores.  Through the regular application of Anti-Spatter Spray, the Work-Table is insensitive to welding beads, dirt, scale, etc.

Material Finish:
ST-52100 -- Heat Treated
Table 32RC --Case Depth .040

Notes:
Base Plate Tables are used in conjunction with Work-Tables or Clamping and Locating Angles.  A Positioning and Clamping bolt is preferable used for Clamping.  Base Elements can be used on both sides.  The front side M9 thread is used for side stops.

Wear Plate

Material Finish:
Aluminum or "HARDOX"
Max. surface hardness up to 55 HB
 

Notes:
Wear plates are used for the protection of table surfaces.  The system-bores are produced 1 mm wider (29 mm) to ensure all elements can be passed through without any problems.  All components being passed through can be fixed using positioning bolts.

HARDOX 550 is a wear plate with a hardness of 550 Brinell and toughness equal to HARDOX 500.  It is intended especially for heavy wear applications and targeted toward users and producers of wear parts using 12% manganese steel castings or 500 Brinell wear plates.  The additional 50 Brinell you gain in hardness when upgrading from 500 HBW steels will increase wear life but not at the expense of crack integrity.

Table Legs

Material Finish:
Steel coated

Our standard leg is capable of holding up to 2 tons.  Product height:  750 mm

With safety in mind, our wheel base version offers a locking brake on 2 of the 4 wheels.  The wheel base leg is capable of holding up to 1 ton.  Product height:  750 mm.

Our height adjustable leg is capable of holding up to 2 tons.  Product height:  750 mm -- 1000 mm.

The clamping tube is fixed in the system bore through tilting.  A deflection of the clamping tube is compensated through the compensating angle.  Therefore a strain on the work piece (position) is excluded.

The swing clamp can be extended through a connection sleeve and a further clamping tube.  The maximum clamping height is 300 mm.  Compensating angle maximum reach is 150 mm or 200 mm.

The clamping pads are changed within seconds.

The deflection of the clamping tube is compensated through the compensating angle.

Note:  all dimensions provided are in mm.

John B. Fulton
CEO--Freer Tool & Supply, Inc.